GE 72279 GE254MVPS-D

GE 72279 GE254MVPS-D T5 High Output Electronic Ballast - 2 or 1 Lamp F54T5HO 120-277V Programmed Rapid Start (UltraStart® low profile, no lead wires)

The GE 72279 GE254MVPS-D is a GE UltraStart® low profile, no lead wires electronic T5 ballast. It operates 2 or 1 lamp configuration on F54T5/47W, F54T5/WM (51W), F54T5/HO lamps, with 120-277V input and Programmed Rapid Start operation.

This ballast should be selected by matching the GE order code, model number, lamp count, lamp type, ballast factor, and input voltage to the existing ballast or fixture label.

Product Overview

GE T5 electronic ballasts in the T5 High Output (2-1 Lamp) family are designed for high-frequency operation of T5 linear fluorescent lamps, with programmed rapid-start circuitry intended to extend lamp life across frequent switching cycles. High Efficiency T5 lamps deliver over 100 lumens per watt for lower operating costs and less glare in office and commercial spaces with lower ceiling heights, while High Output T5 lamps are designed to produce maximum light output for high-bay, industrial, and warehouse facilities and HID-replacement projects.

Ballast factor matters: a ballast factor below 1.00 reduces light output and energy use, a ballast factor at or near 1.00 provides standard output, and a ballast factor above 1.00 increases light output where more illumination is needed — confirm the correct variant for the fixture before ordering.

Technical Specifications

Specifications by Lamp Type — 2-1 – F54T5HO, 120-277V (values shown as 120V/277V where the manufacturer lists dual-voltage figures)

Key Features

• Programmed rapid-start circuitry supports frequent on/off switching without reducing lamp life.
• 120-277V input voltage for common commercial branch-circuit systems.
• Power factor corrected (≥90% on all listed lamp/voltage combinations) for utility compliance.
• Low total harmonic distortion and controlled crest factor across supported lamp types.
• Rated for reliable starting down to -20°F minimum starting temperature.
• Backed by GE’s 5 Years (Electronic Ballast Limited Warranty).

Compatible Applications

• Commercial office buildings and lower-ceiling commercial spaces
• Retail, institutional, and healthcare T5 fluorescent fixtures
• High-bay, industrial, and warehouse facilities (High Output family)
• HID-to-T5 fluorescent retrofit projects
• Indirect and glare-sensitive lighting applications (High Efficiency family)
• Maintenance replacement where GE GE254MVPS-D or GE product code 72279 is specified

Before Ordering Verify

• Exact GE Model: Match GE 72279 / GE254MVPS-D to the existing ballast label or fixture documentation.
• Lamp Type & Count: Confirm the fixture uses one of F54T5/47W, F54T5/WM (51W), F54T5/HO in a 2 or 1-lamp configuration.
• Input Voltage: Confirm the fixture supply matches 120-277V.
• Ballast Factor: Confirm the correct ballast-factor variant (UltraStart® low profile, no lead wires) for the required light output.
• Wiring: Compare existing wiring with the manufacturer’s series-wiring diagram before removing the original ballast.
• Cross-References: Do not substitute another ballast solely from a cross-reference number without confirming lamp count, wiring, ballast factor, and electrical specifications.

Safety & Installation Guidelines

• Qualified Installation: Ballasts should be installed by qualified personnel following applicable electrical codes.
• Disconnect Power: Turn off and lock out power before removing or installing a ballast.
• Grounding: Properly ground the ballast and fixture to reduce EMI/RFI and support safe operation.
• Wiring Diagram: Follow the wiring diagram printed on the ballast label; incorrect wiring can prevent starting or damage the ballast and lamps.
• Lamp Count: Do not connect more or fewer lamps than the ballast is rated for.
• Cap Unused Conductors: Individually cap any unused leads with approved electrical connectors.

Wholesale & Project Support

ADL Supply supports contractors, facility managers, maintenance departments, and commercial buyers with GE T5 ballast replacement identification, project quoting, and volume order support.

For volume pricing, availability, or help confirming the correct GE T5 replacement ballast, contact ADL Supply at 1-800-235-3489.